The normal operation of the flour processing machinery and the quality of the bearing operation

April 15, 2019

As a kind of mechanical equipment, flour processing machinery will inevitably cause problems in operation and affect the normal operation of flour processing machinery.

Improve the operation level of technicians and ensure the production efficiency of equipment in manpower. Flour processing machinery adopts a fully automatic method, which requires an operator to operate. The flour processing machinery operators must carefully learn how to operate the machine to the engineers who install the flour processing machinery. When each set of flour machine is purchased, the manufacturer will explain Its production capacity, as well as its various parameters and performance, it is stipulated that the use of flour processing machinery should be used according to its operating range, in order to avoid damage to the equipment caused by improper operation.

The maintenance of the flour processing machinery can also improve its working efficiency and reduce the occurrence of failures. Before using the flour processing machinery, carefully check the presence or absence of foreign matter in the crushing chamber of Inner Mongolia flour processing equipment. If it is, remove it in time to avoid affecting the quality of the flour. The larger the scale of flour production, the greater the corresponding profit, the greater the risk. Small-scale flour mills have low input costs, low production, and unstable flour quality, which is not competitive in the market. In the large-scale flour mills, the flour processing machinery used is relatively high in automation, and the initial investment is high, but the profit will be high after the stabilization.

During the processing, the mechanical components of the flour processing change, which easily affects the flour extraction rate of the flour processing machine. Operators should pay attention to flexibility. In order to avoid the decrease of efficiency, the grinding of the material can be strengthened at this time, and the material is dispersed into other powder removing machines through the dividing pipe to reduce the load. In order to effectively increase the powder yield, there is a very important basis for accurately understanding the relationship between raw material moisture and flour yield. When the temperature is high and the moisture of the wheat is high, the wind net effect can be appropriately strengthened to reduce the moisture. In the process of washing wheat, the method of lowering the water level and reducing the time of wheat immersion may be adopted according to the situation.

Flour processing machinery should be maintained during use. Flour products can almost be said to be essential for life, which requires continuous improvement of the production efficiency of flour processing machinery to better meet people's food needs. The increase in market demand has increased the processing time of the machine, which is prone to wear and tear during long-term use, and the maintenance of the equipment should be done during use.

Bearing wear problems will inevitably occur during use. In actual production, it can be repaired or replaced according to the degree of wear of the flour processing machinery bearings to ensure the running quality of the bearings and ensure normal operation. At the same time, maintenance work should be done during use to reduce the wear and tear of flour processing equipment components and improve the production efficiency of flour processing machinery. Flour processing machinery bearing installation: The installer also pays attention to the careful installation of the device to ensure the tightness of the connection of the components. After the installation of various devices is completed, it cannot be put into use immediately. It is necessary to test it to ensure that the accessories can run smoothly. If there is an inappropriate place, pay attention to make adjustments again.

In the processing of flour processing machinery, the quality of the material is not good, the sticking is too big, affecting the powder. The processing of the flour processing machinery needs to adjust the parameters and check the whole machine. The material should be dried or replaced with a coarse screen. board. To replace the sieve plate, just open the front cover and you should pay attention to the tightness of the two handwheels when installing the front cover to ensure the front cover is sealed with the casing. Flour processing machinery should stop feeding before parking, let the machine run for 5-20 minutes before parking. In order to reduce residual materials.

During processing, the fineness of the product can be adjusted at any time according to the material, the fineness is uniform, and the trouble during processing can be reduced. There is no need to increase the screening of the sieving machine during the processing of the flour processing machinery. The fully automatic flour processing machine is made of wear-resistant stainless steel, which has good wear resistance, reduces the benefits of frequent replacement parts, and meets the hygiene standards of various products.

The above is the The normal operation of the flour processing machinery and the quality of the bearing operation we have listed for you. You can submit the following form to obtain more industry information we provide for you.

You can visit our website or contact us, and we will provide the latest consultation and solutions

Share to:

Send Inquiry

Previou:Correctly disassemble the vibrating screen bearing properly

Next:What are the uses of the bearings?