Angular touch ball bearing type 70000; consists of outer ring, inner ring, steel ball, holding frame. Can accept radial load and axial load together; can also accept pure axial load; can work stably at higher speed Single-row angular touch ball bearings can only accept axial loads in one direction. These bearings are subjected to pure radial loads; because the roll load effect line and the radial load effect line are not in the same radial plane; internal axial occurs Dividing force; so it is necessary to use the paired equipment.
1. Single row angular touch ball bearing single row angular touch ball bearings have the following layout methods:
(1) Do not leave the angular touch ball bearing This bearing code is S70000; its outer ring raceway side has no lock; can be separated from the inner ring, the support frame, the ball assembly; therefore, it can be separated from the equipment. Miniature bearings less than 10mm; used in gyro-rotor, micro-motors, etc., which have high requirements for dynamic balance, noise, oscillation and stability.
(2) Non-detachable angular touch ball bearings The ferrule channel of such bearings has a lock; therefore, the two sets of rings cannot be separated. According to the touch angle, there are three types:
1 touch angle α=40°; suitable for accepting large axial loads,
2 touch angle α=25°; mostly used for fine spindle bearings,
3 touch angle α = 15 °; mostly used for larger scale fine bearings.
(3) Paired angular contact ball bearings are equipped with angular contact ball bearings for receiving radial loads and axial loads together; they can also accept pure radial loads and axial loads in either direction. The bearings are made by the manufacturer according to the certain preload requirements; the combination is matched and paired; it is provided to the user for use. When the bearing equipment is fastened on the machine; the clearance in the bearing is completely eliminated; and the ferrule and the ball are at Preload condition; thus improving the rigidity of the combined bearing.
There are three different types of equipment for angular contact ball bearings in pairs:
1 back-to-back equipment; the rear code is DB (such as 70,000/DB); this kind of equipment is better in steel; it has good function of accepting overturning moment; the bearing can accept two-way axial load.
2 face-to-face equipment; the rear code is DF (such as 70,000/DF); the rigidity of this equipment and the ability to accept the overturning moment are not as good as the DB equipment method; the bearing can accept two-way axial load,
3 series equipment; rear code is DT (such as 70,000 / DT); this equipment can also be connected in series with three or more bearings at the same bearing; but can only accept axial load in one direction. Usually; for balance and restraint The axial displacement of the shaft; the other bearing requires the bearing to receive the axial load in the other direction.
In addition, there is a single-row angular touch ball bearing that can be easily paired. This type of bearing is specially machined; it can be combined in two back-to-back, two face-to-face or two series connection; the axial clearance of the paired combination can be selected according to requirements. The post-code CA indicates that the axial void is more moderate than the CB, and the axial void is moderate.
All-round matched bearings; can also be equipped with pre-interference bearing according to the application requirements; and later coded GA, GB, GC indicate that .GA indicates a small pre-interference after pairing, GB indicates that there is a medium pre-match after pairing Ying, GC indicates that there is a large pre-interference after pairing.
2.
Double Row Angular Contact Ball Bearing double row angular touch ball bearing is characterized by the ability to accept the combined load of radial and axial loads together; the axial displacement of the two sides of the constrained shaft. Compared with the two-way
Thrust Ball Bearing; Higher; the touch angle is 32°; the rigidity is good; the overturning moment is acceptable; it is widely used in the front wheel hub of a car (some models also use double-row
Tapered Roller bearings of the same scale).
There are four variations on the layout of double row angular touch ball bearings:
(1) Specification of A-type outer diameter less than or equal to 90mm bearing. No ball gap; thus can accept flat two-way axial load. Lightweight glass fiber reinforced nylon 66 support frame is adopted; bearing temperature rise is small.
(2) Specification of bearing type A with outer diameter greater than 90mm. There is a ball gap on one side; equipment steel plate stamping bracket or brass body holder.
(3) E type is a reinforced layout; one side has a ball gap; it can hold more steel balls; thus the bearing capacity is higher.
(4) Double-row angular touch ball bearings with dust-proof cover on both sides and two-sided seal type A and E-type depicting can be equipped with dust cover (non-touch) or seal (touch) on both sides The inside of the sealed bearing is filled with rust-proof lithium-based smooth grease; the operating temperature is usually -30 ~ +110 ° C. No need to be smooth in the application time; should not be heated before the equipment;
Double-row angular touch ball bearing equipment should be paid attention to; although the bearing can accept two-way axial load; if there is a ball gap on one side; then should pay attention not to let the primary axial load pass the notched side of the groove.
